[The logo is protected from the company]

Cameron International Corporation

Cameron is a leading provider of flow equipment products, systems and services to worldwide oil, gas and process industries. Leveraging its global manufacturing, engineering and sales and service network, Cameron works with drilling contractors, oil & gas producers, pipeline operators, refiners and other process owners to control, direct, adjust, process, measure and compress pressures and flows.  Read More

Address      1333 West Loop South Suite 1700 Houston, TX 77027
Website      www.c-a-m.com/
Holding      No Holding Details

View Company Page
Apply to job

Mechanical Engineer

• Review customer applicable specifications to confirm design compliance for the application. (Request clarifications or provide exceptions list).
• Create “Design Basis” document specific to the particular project. The document is based on the applicable Codes, client specifications, Cameron scope of supply, and approved exception list.
• Perform ASME Code VIII-1/2 calculations with all applicable design loads and design combinations in accordance with the “Design Basis”.
• With all applicable design loads and combinations, including tie-down, lifting, jacking up, etc., perform vessel support design and design of lifting devices, as required.
• With all applicable design loads and combinations, perform structural weld sizing as required.
• If applicable, perform a fatigue analysis of the vessel, (using FE-Pipe or other software).
• With all applicable design loads and combinations, perform structural member and weld sizing for vessel internal supports, as required.
• Coordinate with Drafting Department to identify locations of nozzles, supports and other vessel attachments.
• Provide necessary dimensional sketches and engineering instructions to Drafting Department, as required.
• Assist in providing necessary design information to an engineering contractor, as required.
• Review and approve, as required, subcontractor calculations and drawings to ensure compliance with client specifications or applicable standards.
• Assist other locations and branches with mechanical / structural engineering design, as required.
• Provide preliminary vessel and structural beam weights.
• Review vessel drawings and re-run calculations, as required, to ensure conformity.
• Provide input to the “Lessons learned” process
• Provide technical support for troubleshooting.
• Check the work by others as required.
Job Requirements/ Qualifications    EDUCATIONAL REQUIREMENTS
• A diploma or degree in Mechanical Engineering
DESIRABLE TRAITS AND SKILLS:
• Fully numerate and computer literate
• Good communication skills, both written and verbal, at all levels of the business
• Good understanding of material requirements and codes and standards applicable to Oil & Gas process equipment
• Self motivation, initiative and commitment
• Hardworking, enthusiastic and energetic
• Honest and high integrity
• Excellent organizational skills
• Neatness and attention to detail
• Adaptable and flexibile
• Dependable
• Creative

PREFERRED CANDIDATE

The preferred candidate will have
Working Knowledge of ASME B&PV Code VIII-1
8-10 years experience in the design of oil, gas or water related Process Equipment.
LEVEL OF EXPERIENCE
To be considered for this position the selected candidate should possess the following.
• Engineering degree with 8-10 years of relevant experience within the oil and gas industry.
• Strong knowledge of international mechanical design codes and programs commonly used in the petroleum industry.
• Knowledge of fabrication techniques for vessels, piping and structure etc, and also the associated testing techniques and established industry QC requirements.
• General knowledge of oil and gas production, hydrocarbon processing and oil/water separation.
• Some knowledge of structural and/or pipe stress design and analysis.
• Experience in personal computers, spreadsheets and word processing as well as good written and verbal communication skills.

ESSENTIAL FUNCTIONS:
The Mechanical Engineer will be required to communicate in English in both written and verbal form.

Other Job Information

Vacancy type:

Full Time

Contact Mode:

not provided

Fax:

713.513.3456

Contact Name:

not provided

Job Duration:

not provided

Phone:

713.513.3300

Email:

not provided

News - Cameron International Corporation

Related Jobs

1st Class Mechanic Electrical

DescriptionQualifications: Must possess skills and abili ...   [more]

2nd Class Mechanic Mechanical

DescriptionMust have three (3) years mechanical experien ...   [more]

1st Class Mechanic Electrical

DescriptionQualifications: Must possess skills and abili ...   [more]

1st Class Mechanic Mechanical

Description Candidates must possess skills and abilities ...   [more]

Mechanical Engineer

Description We are currently recruiting for a Mechanical ...   [more]

Automotive & Equipment Mechanic

Job Responsibilities:Experience the personal challenge o ...   [more]

Automotive & Equipment Mechanic

Job Responsibilities:Diagnose, repair and perform preven ...   [more]

Mechanic

Job Responsibilities:      We are currently seeking an e ...   [more]

Expand

Collapse