[The logo is protected from the company]

Boeing

Boeing is an American multinational aerospace and defense corporation, founded in 1916 by William E. Boeing in Seattle, Washington. Boeing has expanded over the years, merging with McDonnell Douglas in 1997. Boeing Corporate headquarters has been in Chicago, Illinois since 2001. Boeing is made up of multiple business units, which are Boeing Commercial Airplanes (BCA); Boeing Defense, Space & Security (BDS); Engineering, Operations & Technology; Boeing Capital; and Boeing Shared Servic... Read More

Address      not provided
Website      www.boeing.com
Holding      No Holding Details

View Company Page
Apply to job

Plastics Assembler

Mechanics in this position assemble and install various composite and metal parts/assemblies for the wing and fuselage sub assemblies. These sub assemblies are later incorporated in larger assemblies that are subsequently installed on the airplane. Employment in this position also requires occasional (1-3 hours) lifting and carrying less than 10 pounds, rotation of head/neck, standing, walking, use of low impact vibratory tools, finger manipulation, flexion/extension, contact with metals, plastics, solvents and the use of personal safety gear for face, eyes, hand and ears. Additional Tasks, Duties and Responsibilities: Locate work area using drawings which specifies airplane number, section number, and three-point location. Obtain and verify kitted (pre-picked) detail parts, standards, and assemblies were issued correctly. Ensure that parts issued are effective for the airplane and are free of visible defects. If parts are not pre-picked, get parts and ensure that parts selected are effective for the airplane and are free of visible defects. Set up assembly tools per tooling instructions or drawing. Review bar chart or automated time line to determine which job to work on and obtain appropriate drawings for job. Locate tools and/or parts on airplane using tooling holes, pilot holes, K holes, or by hand (as required), per drawing or tooling instructions. Align parts and secure in place using Clecos or tooling/hand clamps. Check for good edge margins and alignment. Shim and/or trim parts. Select drill bits, reamers and/or countersinking tools for pilot and full size holes. Drill pilot holes using drill motor and proper size drill bit(s). Drill, ream, countersink full size holes in parts/assemblies, in proper sequence and to correct size using drill motor. Set countersinking tools to proper depth. Disassemble parts and deburr holes using chip chasers, deburring tools, and files to prepare for installation of fasteners. Use solvents to clean surfaces prior to sealing or assembly. Apply sealant, alodine, primer, adhesives, and special finishes. Load and unload ovens to bond detail parts to assemblies. Apply permanent or temporary part mark and protective material to assemblies for preparation of shipment. Handle and dispose of hazardous materials in approved manner. Determine and obtain correct type and size fasteners. Install fasteners in correct sequence per drawing, using correct tools (e.g., rivet gun and bucking bar, drill motor, power screwdriver, C-squeeze, ratchet wrench, nut runner). Check work after completion of each operation in job and/or completed job to ensure it is complete per drawing.

Other Job Information

Vacancy type:

Full Time

Contact Mode:

email

Fax:

not provided

Contact Name:

not provided

Job Duration:

not provided

Phone:

not provided

Email:

not provided

TalentOne Job Information

Engineering Production Engineer

Open Jobs - Boeing

News - Boeing

Related Jobs

Director of Product Management

 Company profile: NETGEAR, a US public company (NTGR), h ...   [more]

Senior Enginnering Product Manager

 Job Description    * Own revenue and profitability targ ...   [more]

Sr Engineering Product Manager

 As a member of the Service Provider Engineering team, y ...   [more]

Industrial Engineer

Description The successful candidate will act as a liais ...   [more]

Performance and Scalability Engineer

 Principal Duties:Develop performance tests, analyze tes ...   [more]

Production Engineers

The key responsibilities of this position include: Dril ...   [more]

Product Engineer

Responsibilities include engineering and development eff ...   [more]

Product Engineer

Review customer inquiries, prepare proposals, and design ...   [more]

Expand

Collapse